Scott Penrose
65 lines
2.0 KiB
INI
65 lines
2.0 KiB
INI
; Self-contained PlatformIO project for the AutoProvision example.
|
|
;
|
|
; Host boards are provided — pick one with -e:
|
|
; pio run -e esp32-s3-devkitc-1 -t upload # generic ESP32-S3 dev board
|
|
; pio run -e xiao-esp32s3 -t upload # Seeed XIAO ESP32-S3
|
|
; pio run -e xiao-esp32c3 -t upload # Seeed XIAO ESP32-C3
|
|
; pio device monitor
|
|
;
|
|
; The radio region is set via build flags — the same LORA_* defines you'd use
|
|
; when compiling MeshCore firmware. The host UART pins differ per board because
|
|
; the XIAO does not break out GPIO17/18.
|
|
;
|
|
; The library is pulled from the repo root (two levels up) via a relative
|
|
; symlink dependency, so there's no copy of the source.
|
|
|
|
[platformio]
|
|
default_envs = esp32-s3-devkitc-1
|
|
|
|
[common]
|
|
platform = espressif32
|
|
framework = arduino
|
|
monitor_speed = 115200
|
|
lib_deps = symlink://../..
|
|
build_flags =
|
|
-D UART_BAUD=115200
|
|
; AU narrow band radio region
|
|
-D LORA_FREQ=916.575
|
|
-D LORA_BW=62.5
|
|
-D LORA_SF=7
|
|
-D LORA_CR=8
|
|
-D LORA_TX_POWER=20
|
|
|
|
[env:esp32-s3-devkitc-1]
|
|
extends = common
|
|
board = esp32-s3-devkitc-1
|
|
build_flags =
|
|
${common.build_flags}
|
|
; host UART pins to the companion
|
|
-D UART_RX_PIN=17
|
|
-D UART_TX_PIN=18
|
|
|
|
[env:xiao-esp32s3]
|
|
extends = common
|
|
board = seeed_xiao_esp32s3
|
|
build_flags =
|
|
${common.build_flags}
|
|
; host UART pins to the companion (XIAO pads D7=GPIO44 RX, D6=GPIO43 TX)
|
|
-D UART_RX_PIN=44
|
|
-D UART_TX_PIN=43
|
|
; the XIAO has only native USB (no UART bridge) — route Serial to USB-CDC so
|
|
; the monitor sees output. (The devkit doesn't need this; it has a CP2102.)
|
|
-D ARDUINO_USB_MODE=1
|
|
-D ARDUINO_USB_CDC_ON_BOOT=1
|
|
|
|
[env:xiao-esp32c3]
|
|
extends = common
|
|
board = seeed_xiao_esp32c3
|
|
build_flags =
|
|
${common.build_flags}
|
|
; host UART pins to the companion (XIAO C3 pads D7=GPIO20 RX, D6=GPIO21 TX)
|
|
-D UART_RX_PIN=20
|
|
-D UART_TX_PIN=21
|
|
; native USB only (USB-Serial/JTAG) — route Serial to USB-CDC for the monitor
|
|
-D ARDUINO_USB_CDC_ON_BOOT=1
|