105 lines
3.5 KiB
INI
105 lines
3.5 KiB
INI
; PlatformIO Project Configuration File
|
|
; ESP32 Debug Dongle - Web Serial Terminal with Bluetooth
|
|
;
|
|
; Build and upload:
|
|
; pio run -t upload
|
|
;
|
|
; Upload filesystem (LittleFS with web files):
|
|
; pio run -t uploadfs
|
|
;
|
|
; Monitor serial output:
|
|
; pio device monitor
|
|
|
|
[env:esp32dev]
|
|
platform = espressif32
|
|
board = esp32dev
|
|
framework = arduino
|
|
monitor_speed = 115200
|
|
monitor_filters = esp32_exception_decoder
|
|
|
|
board_build.filesystem = littlefs
|
|
|
|
; Use a larger app partition (pick ONE):
|
|
board_build.partitions = huge_app.csv ; 3MB app, 1MB FS, no OTA
|
|
; board_build.partitions = no_ota.csv ; 2MB app, 2MB FS, no OTA
|
|
; board_build.partitions = min_spiffs.csv ; 1.9MB app + OTA, 190KB FS
|
|
|
|
build_flags =
|
|
-DCORE_DEBUG_LEVEL=3
|
|
-DCONFIG_BT_ENABLED=1
|
|
-DCONFIG_BLUEDROID_ENABLED=1
|
|
-DHAS_BT_CLASSIC=1 ; classic SPP exists on the original ESP32
|
|
-DSTA_SSID="${sysenv.STA_SSID}"
|
|
-DSTA_PASSWORD="${sysenv.STA_PASSWORD}"
|
|
|
|
; Libraries
|
|
lib_deps =
|
|
; Async Web Server and dependencies
|
|
https://github.com/ESP32Async/ESPAsyncWebServer
|
|
https://github.com/ESP32Async/AsyncTCP
|
|
|
|
; ArduinoJson for configuration/commands
|
|
ArduinoJson
|
|
|
|
; Upload settings (adjust port as needed)
|
|
; upload_port = /dev/ttyUSB0
|
|
; upload_speed = 921600
|
|
|
|
; Extra scripts for LittleFS
|
|
extra_scripts =
|
|
pre:scripts/download_xterm.py
|
|
|
|
; ============================================================================
|
|
; LilyGo T3-S3 -- ESP32-S3 + SX127x LoRa + SSD1306 128x64 OLED + microSD.
|
|
; The remote debug bridge: UART <-> telnet(:23)/WebSocket, GPIO reset/wake,
|
|
; SD logging (NTP-dated), OLED status. NOTE: ESP32-S3 has NO Bluetooth Classic,
|
|
; so HAS_BT_CLASSIC is NOT set here (telnet + WebSocket replace SerialBT).
|
|
; Pins marked CONFIRM must be checked against your actual board wiring.
|
|
; ============================================================================
|
|
[env:t3s3]
|
|
platform = espressif32
|
|
board = esp32-s3-devkitc-1
|
|
framework = arduino
|
|
monitor_speed = 115200
|
|
monitor_filters = esp32_exception_decoder
|
|
board_build.mcu = esp32s3
|
|
board_build.flash_size = 4MB
|
|
board_upload.flash_size = 4MB
|
|
board_build.filesystem = littlefs
|
|
board_build.partitions = huge_app.csv
|
|
build_flags =
|
|
-DCORE_DEBUG_LEVEL=3
|
|
-DARDUINO_USB_CDC_ON_BOOT=1 ; console on USB CDC -> frees UART0 (43/44)
|
|
;-DSTA_SSID="${sysenv.STA_SSID}"
|
|
;-DSTA_PASSWORD="${sysenv.STA_PASSWORD}"
|
|
-DSTA_SSID="MeridenRainbow5G"
|
|
-DSTA_PASSWORD="4z8bcw5vfrs3n7dm"
|
|
-DBOARD_T3S3=1
|
|
; --- OLED (SSD1306 128x64) ---
|
|
-DT3S3_OLED_SDA=18
|
|
-DT3S3_OLED_SCL=17
|
|
-DT3S3_OLED_RST=21
|
|
-DT3S3_OLED_ADDR=0x3C
|
|
; --- target UART bridge (wire to the sensor's debug UART) ---
|
|
-DTARGET_RX_PIN=44 ; CONFIRM: dongle RX <- sensor TX
|
|
-DTARGET_TX_PIN=43 ; CONFIRM: dongle TX -> sensor RX
|
|
; --- GPIO control lines to the target (reset / wake) ---
|
|
-DGPIO_RESET_PIN=2 ; CONFIRM: -> sensor RST
|
|
-DGPIO_WAKE_PIN=1 ; CONFIRM: -> sensor control/wake pin
|
|
-DGPIO_CTRL_ACTIVE_LOW=1
|
|
; --- microSD (CONFIRM: may share the LoRa SPI bus + own CS) ---
|
|
-DT3S3_SD_SCK=5
|
|
-DT3S3_SD_MISO=3
|
|
-DT3S3_SD_MOSI=6
|
|
-DT3S3_SD_CS=13
|
|
; --- timezone for NTP-dated logs (Australia/Victoria) ---
|
|
-DNTP_TZ='"AEST-10AEDT,M10.1.0,M4.1.0/3"'
|
|
lib_deps =
|
|
https://github.com/ESP32Async/ESPAsyncWebServer
|
|
https://github.com/ESP32Async/AsyncTCP
|
|
ArduinoJson
|
|
adafruit/Adafruit SSD1306
|
|
adafruit/Adafruit GFX Library
|
|
extra_scripts =
|
|
pre:scripts/download_xterm.py
|